高尔夫导视制作时的工艺流程的具体操作方法

高尔夫导视制作时的工艺流程的具体操作方法

    （一） 高尔夫导视制作时需要的是表面保护措施
    高尔夫导视制作的涂耐腐蚀的感光油墨，这是一基本的设施。
    在我们制作高尔夫导视制作时首先选择200目的丝网网版。在这些丝网网版必须特干净,大小适中。然而这是一些过程，然后把它牢牢固定在专业的手工网印平台架子上，把不锈钢板放在丝网网版的中心位置，高尔夫导视制作让不锈钢板的边与对应的丝网网版内框保持6厘米左右的距离,太近和太远都不合适。通过这些一系列化的策划之后，然后，放在恰当的位置后，用透明胶带粘在四周 ，粘的时候一定要仔细地用手边粘边压,这样才不会在透明胶带和网版之间留有气泡,让它们充分接触，在涂感光油墨时不会涂到不锈钢板外面。中间没粘透明胶带部分正好和不锈钢板的大小吻合，这样在涂耐腐蚀的感光油墨的时候，位置才会准确。全部粘好后，把表面再清理一下，以保持丝网网版纱面的清洁。这就是我们在高尔夫导视制作时的一些基本的操作方法。

    那么，高尔夫导视制作时的丝网网版如何制作呢，我们选择一块1厘米厚的垫板，把它放在丝网网版与网印平台架子面板的后面，它们之间的这个距离，这就是网距。一般最好是使丝网网版张力大，网距小.，这样刮印油墨后能及时弹起。在这些过程里，我们力所做到的就是需要精准的手工工艺。

    高尔夫导视制作时还会用到腐蚀这一过程，然而耐腐蚀的感光油墨在使用前，要调整稀稠度，在冬天，油墨很容易凝固。可以先把它放在烘箱里烘一会儿。烘箱的温度设置在88度，让它自动控制，5分钟后拿出来，充分搅拌，没有气泡，像这样了才能使用。这些都是在实际的过程中得到的一些经验之谈。

    在高尔夫导视制作时准备一把斜面有弹性、平整、无缺口，表面干净的橡胶刮板。
    再就是准备进口的油墨，在制作时把适量的感光油墨,放在丝网网版的纱面上,形成一个条状，就可以用刮板开始刮了，刮的时候，用力要合适，速度也要恰到好处，刮1到2遍后，把丝网网版掀开，如果印在不锈钢板上的感光油墨厚薄非常均匀，就可以用手托在它的反面，把它拿出来，注意不要将涂有感光油墨的那面弄脏。这需要严格的管理制度来限制这些过程。要说明的是， 经常会遇到这样的情况，刮2遍后，效果还是不好，那就要放弃了。否则油墨太厚也是不行的。这些经验老练的师傅就才会知道这些。

    我们在制作时要调好水温，在30度左右的温水中，加入适量工业用弱碱性的碳酸钠，比例大约是20：1，搅拌均匀后放入感光油墨没有涂均匀的不锈钢板，涂层很快就会脱离不锈钢表面，再用干净的布把感光油墨彻底擦掉，然后用清水漂洗，用吹风机吹干，就可以重新再印了。把这些工作一步一步地做好，让我们的高尔夫导视制作成精品的工艺品。

Golf guides making process when specific methods of operation

    (A) golf guides produced when the surface protection measures required
    Golf guides produced by the light-sensitive ink corrosion-resistant coating, which is a basic infrastructure.
    Guides produced in our production of golf when the purpose of the first 200 mesh screen selection. In these special mesh screen must be a clean, medium size. However, this is some of the process, then it is firmly fixed in the professional manual screen printing platform on the shelf, the stainless steel mesh screen on the center, so that the side with stainless steel mesh screen in the corresponding box to keep 6 cm distance, too close and too far were inappropriate. These, after a series of planning, then, on the appropriate location, use scotch tape all around, stick time must be carefully pressed by hand, sticky side, so as not to screen in transparent tape and between leave air bubbles, so that their full contact, light-sensitive ink on coated stainless steel plate will not be applied to the outside. The middle part just did not stick transparent tape and stainless steel plate the size of the match, so that the light-sensitive ink coated corrosion-resistant when the position will be accurate. After all stick to the surface and then clean up, to keep the screen clean gauze screen. This is what we make in golf guides to some of the basic method of operation.

    So, when making golf guides how to make it mesh screen, we chose a 1 cm thick plate, put it on the wire screen and screen printing platform shelf behind the panel, the distance between them, This is the network distance. Generally it is desirable to screen a large screen tension, mesh away from the small.. This timely after scraping India ink bounce. In these processes, we need to do is force the precise craftsmanship.

    Golf guides will be used when making the corrosion process, corrosion-resistant light-sensitive ink, however, before use, dilute to adjust the consistency, in the winter, the ink is easy to solidification. Can put it in the oven while baking. Set oven temperature at 88 degrees, it automatically controls out after 5 minutes, stir, no bubbles, like the case to use. These are in the actual process to get some of the voice of experience.

    In golf guides prepare a slope when making flexible, smooth, no notch, clean the surface of the rubber scraper.
    Then there are ready to import the ink, the amount of time in the production of light-sensitive ink, on the yarn surface mesh screen to form a strip, you can use a scraper start scraping, scraping, when forced to the right, the speed should be just right, 1 to 2 times after scraping, the mesh screen opened, if printed on stainless steel plate thickness is very uniform light-sensitive ink, you can use the opposite hand under it, take it out, be careful not to coated with light-sensitive ink that side dirty. This requires strict management system to limit these processes. To note is that often encounter such a situation, scraping two times, the effect or not, it would have to give up. Otherwise, the ink is too thick will not work. Seasoned master on these experiences will know.

    We should be fine in the production of water temperature, 30 degrees in the warm water, add appropriate amount of alkaline sodium carbonate for industrial use, the ratio is about 20:1, even after mixing into the light-sensitive ink is not uniformly coated stainless steel plate, coated will soon be out of stainless steel surface layer, and then clean cloth to thoroughly wipe sensitive ink, then rinse with water, dried with a hair dryer, you can re-printed. Step by step to make these work, let our guides made into fine golf crafts.