深圳酒店不锈钢制作时的涂好感光油墨烘干的作用！

深圳酒店不锈钢制作时的涂好感光油墨烘干的作用！

    在企业制作标识牌不钢刚时，有时会需要丝印一些图案，作为标识牌制作公司，把涂好感光油墨的不锈钢板放在烘箱里，温度设置在88度，烘的时间为15到20分钟。这个时间需要把握好时间度，时间的控制和温度的控制，是整个过程的最关健点，在标识牌烘干后，把吹风机调到冷风档，给不锈钢板降温，也可以让它自然降温。自然体现企业品牌的形象设计。

    酒店标识牌制作时的印刷曝光来制作一些图案纹理。
    我们在标识牌时，企业的标识牌设计创意就是如下开始的，下面到kR-B1型单面真空曝光机上进行曝光。这是需要一些设备来处理这些问题的。在先接通电源，控制面板上的电流表显示为8安-10安，将机器预热3分钟左右，即可正常工作。将菲林片与不锈钢板对齐并使两者充分接触，然后让不锈钢板在上面，菲林片在下面，平稳地放在单面真空曝光机工作台面上。一定要注意这些表面的干净一些，否则就会一一些印子在上面，这样做的标识牌就没那么好看了。

    企业品牌创意设计，就用这些品牌来设计过的，我们在制作时取出不锈钢板和菲林。这就是曝光后的不锈钢板，用肉眼看上去，没有任何变化。再曝光工作完成后，一定要过5分钟，让曝光机内的灯管冷却后，再关闭总电源。这样就把这些酒店的不锈钢标牌制作完成的了。

Coated stainless steel business is good when the role of light-sensitive ink drying!

     Signage in the corporate production of stainless steel just, sometimes need to screen some of the design, production companies as signage, good light-sensitive ink to coated stainless steel plate on the oven, the temperature set at 88 degrees, bake time is 15 to 20 minutes. This time need a good grasp of time, time control and temperature control, the whole process is the most Key points in the identification card, after drying, the hair dryer transferred to the cold file, to the stainless steel plate cooling, you can let it cool down . Naturally reflect the corporate brand image design.

     Identification card when making the printing exposure to make some of the texture pattern.
     We signage, corporate logo design creative brand is as the beginning of the following to the kR-B1-type vacuum exposure machine on single exposure. This is some of the equipment needed to deal with these issues. Earlier power, current meter on the control panel display is 8 -10 An An, preheat the machine about 3 minutes, you can work. Films will be aligned with the stainless steel plate and make full contact between the two, and then let the stainless steel plate on the top film sheet below, smooth on one side vacuum exposure machine work surface. Must pay attention to some of these surfaces clean, otherwise it will mark a number on it, so do not be so good-looking signage.

     Brand creative design, we use these brands to design before, when we made ​​out of stainless steel plates and film. This is the exposure of the stainless steel plate, with the naked eye, without any change. Re-exposure is completed, must be over 5 minutes to allow the lamp cooling exposure machine, then turn off the power. This put them in the hotel finished a stainless steel plate.