专业的酒店标牌公司在酒店标识制作时的基本流程和工艺！

专业的酒店标牌公司在标识制作时的基本流程和工艺！

    酒店标识制作时的配液如何配制！
    作为一些企业的标识制作的工艺是，用作蚀刻剂的是三氯化铁溶液。它的波美浓度在蚀刻环节中非常重要，直接影响到蚀刻的速度。合适的波美浓度是38到40度之间。
测量浓度的方法是；将三氯化铁溶液倒在细长的量杯中，插入波美计，挨着液面的数值就是它的波美浓度。

    酒店标识制作的配比浓度，现在的波美浓度是42度，有些太浓，酒店标识制作我们可以加水进行稀释，搅拌均匀后，取样重新进行測量。如果波美浓度太低，则可加入高浓度的三氯化铁溶液。波美浓度调配合适后，倒入蚀刻机的箱体内，把盖子盖好。

   酒店标制识制作的如何开机，蚀刻机使用的是380V电源。打开电源开关，电源指示灯亮。启动酸泵，让三氯化铁溶液在机器内循环，观察温度表最高不能超过50度。按下传送带开关，进行整机试运行。

    酒店标牌制作的工艺如何好，试刻这台精密摇摆蚀刻机传送带可以无级调速，冲刷时间的长短可以在这里进行调整。蚀刻机运转正常后，先在入料口放一块试刻用的不锈钢板，传送带会把它缓慢的送入机器内部。按下蚀刻开关，机器内的喷嘴就开始喷出三氯化铁溶液，它的压力基本上是恒定的。三氯化铁溶液不断地冲刷不锈钢板的表面，溶液中的三价铁离子快速氧化不锈钢板，不锈钢板就被蚀刻下去了。要如何制作就是如何开始。你就是这样的制作公司形象化。

Professional sign company in the identification process and the production process when the basic!

     Identify how to make time with a liquid preparation!
     As some companies make the identification process is used etchant is ferric chloride solution. It's part of Baume concentration is very important in the etching, a direct impact on the speed of etching. The appropriate concentration of 38-40 Baume degrees.
 Concentration is measured; the ferric chloride solution to the slender measuring cup, insert Baume meter, it is next to the value of surface concentration of Baume.

     Identify the production ratio of the concentration, the concentration is now 42 degrees Baume, and some too strong, we can be diluted with water, mixing evenly, the sample re-measured. If Baume concentration is too low, you can add high concentrations of ferric chloride solution. Baume concentration deployment of suitable, into the etching machine cabinets, the lid cover.

    Standard system of knowledge production to boot, etching machine using a 380V power supply. Turn on the power switch, power indicator light. Start the acid pump, so that ferric chloride solution in the machine cycle, observe the thermometer may not exceed 50 degrees. Press the belt switch, the whole test run.

     How good sign production process, test swing carved this etching machine precision variable speed conveyor belt can, scouring the length of time can be adjusted here. Etching machine in normal operation, the first I put a feeding trial with engraved stainless steel plate, it will slow conveyor belt into the machine. Etching press switch, the machine began to spray nozzle ferric chloride solution, it is essentially constant pressure. Ferric chloride solution constantly scouring the surface of stainless steel plate, the solution of ferric ion rapidly oxidized stainless steel plate, stainless steel plate was etched on the go. How to make is how to begin. You are such a production company to visualize.